Heated mirror pads

A heated mirror pad ensures clear mirrors straight after a hot bath or shower​


Mirror 3

Simple installation

Simply fix the back of the mirror with self adhesive backing and connect to the lighting circuit.

Safe in bathrooms

The heated pad is concealed behind the mirror and all electrical connections are within the wall of ceiling cavity.

Low profile

Only 1mm thick with a low profile 5mm connection.

Energy efficient

The low voltage output doesn't use much energy to keep your mirrors steam-free. Typically consumes less power than the average light bulb.

Stock CodeDescriptionShapeHeight x Width (mm)Output (w)Unit
MH-0600Mirror HeaterRectangular400 x 60057Ea
MH-0800Mirror HeaterRectangular600 x 80096Ea
MH-0900Mirror HeaterRectangular600 x 900108Ea
MH-1000Mirror HeaterRectangular750 x 1000150Ea
MH-1200Mirror HeaterRectangular850 x 1200204Ea
MH-1300Mirror HeaterRectangular1000 x 1300260Ea
MHO-0600Mirror HeaterOval400 x 60045Ea
MHO-0800Mirror HeaterOval600 x 80076Ea
MHR-0380Mirror HeaterRound380ø20Ea
MHR-0530Mirror HeaterRound520ø41Ea

Installation accessories

Stock CodeDescriptionSize
MH-DSTDouble Sided Tape25 x 50 mm
MH-ADHMirror Adhesive310 ml
PIR-01PIR Movement Sensor-

Install in 4 easy steps

Mirror Installation Step 1

Adhere heater to back of your mirror

Use the self adhesive backing to fix the mirror heater to the back of your mirror. Mirror adhesive should be applied around the perimeter of the mirror so it becomes as isolated as possible when fixed to the wall, we recommend ThermoSphere mirror adhesive.

Lay your mirror onto a clean towel to ensure no scratches or blemishes are formed when applying the heated element.

Heated Mirror Installation Step 2

Wire up and fix to the wall

Wire the demister pad into a marshalling box behind the mirror. Then line the mirror up ensuring a 5mm gap is maintained around the perimeter of the mirror if installing flush with tiles. Gently apply pressure around the outside of the mirror and allow all adhesives to fully cure before powering up your mirror.

If you are using mechanical fixings, ensure they are not within 10mm of the heater pad.

Heated Mirror Installation Step 3

Wiring to a light circuit

ThermoSphere mirror demisters require a mains supply, marshalling box and a switch or PIR sensor. Measure and mark out all the necessary items before you install the electric mirror heater. If necessary chase into the wall to accommodate fixtures and wires.

If you are installing your mirror into a rebate within the tiles ensure you leave a 5mm gap around the perimeter of the mirror. Any contact with the hard materials could result in a breakage

Heated Mirror Installation Step 4

Wiring to a PIR sensor

Can be wired into an existing lighting circuit. You can also connect to a PIR (Movement) sensor if needed.

Remember to position the connection box and power cable in the closest available position to your electrical connections.

Pro tips

If you are installing your mirror into a rebate within the tiles ensure you leave a 5mm gap around the perimeter of the mirror. Any contact with the hard materials could result in a breakage.

The heated mirror can be installed on walls made of wood, ceramic tiles, marble etc. Walls must be dry, stable, smooth and preferably insulated.

To avoid damage to the mirror, do not over tighten fixings and ensure that no point pressure is applied to the mirror.

Your Items

Get in touch with us

Membrane floor build up
Foil floor build up
Screed floor build up
Mesh floor build up

We close at 5pm on 24th Dec and reopen at 7.30am on 4th Jan 2022.

Orders for next day delivery will need to be placed by 4.30pm on the 23rd Dec.

Got a question about this?